Crankshaft
All Crankshaft products 179
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
Air Compressor, Crankshaft
No products on this page match the filter.
What is an air brake compressor crankshaft?
An air brake compressor crankshaft is the main shaft inside the air compressor of trucks and buses that transfers rotation from the engine to the pistons. The crank throws and bearing journals on the shaft convert rotation into the back-and-forth motion of the pistons. Because the crankshaft converts rotation into reciprocating motion, it sits at the center of the compressor's working cycle. In the field this part is also called the crank shaft or simply the crank. As the most heavily loaded part of the compressor that constantly rubs against its bearing surfaces, its condition directly affects the health of the entire compressor.
How does the air brake compressor crankshaft work and what does it include?
The compressor's motion chain starts with the crankshaft and reaches the pistons through the connecting rods. Because load and friction change at every stage of the movement, the shaft and its bearings must work together in harmony. The main components found in the crankshaft assembly are:
- Crankshaft: the main body that carries the rotation; it transfers load and vibration to the bearings.
- Bearing and bushing: the surfaces on which the shaft turns; they reduce friction and keep the shaft in place.
- Connecting rod seats: the slots on the shaft to which the pistons' connecting rods are attached.
- Drive element: the gear or pulley structure that transfers motion from the engine to the compressor.
- Seal and gasket: the sealing parts that prevent oil and air from leaking out of the compressor housing.
- Oil passages: internal channels that deliver oil to the bearing surfaces.
Air brake compressor crankshaft types
- Complete crankshaft: comes with the bearings and bushings attached to the shaft; preferred when both shaft surface and bearings show wear together.
- Shaft only: considered when the bearings and bushings are sound and only the shaft surface is worn.
- Type by drive: compressors that receive motion from the engine via gear or pulley can have different connection surfaces and drive elements, so drive type must be determined first.
How to choose the right air brake compressor crankshaft?
Selection should be based on the part marking on the removed crankshaft, the shape of its connection surfaces, and the drive type of the compressor. The engine and vehicle model the compressor is fitted to must also be checked. A preliminary match can be made by showing the old crankshaft's photo and the markings on the part to the supplier. Even within the same model series of brands such as Mercedes-Benz, MAN, Scania, Volvo and DAF, different layouts may exist, so choosing by model name alone is a mistake.
| Criterion | What to check | Why it matters |
|---|---|---|
| Drive type | Whether motion from the engine is transmitted by gear or pulley | Connection surfaces and drive element can differ |
| Shaft surface | Scratches, wear and ovality on the bearing surfaces | Determines the extent of the part to be renewed |
| Bearing and bushing condition | Play in the shaft and noise while rotating | Determines whether a complete crankshaft or shaft only is needed |
| Oil passages | Blockage and openness of the passages | Can be the source of lubrication shortage |
| Housing seating surface | Surfaces that contact the compressor housing | Wrong part fitting breaks the seal |
Installation and maintenance points
- Open the oil passages: before fitting the crankshaft, all oil passages must be cleaned and checked to be open.
- Lubricate the bearings: bearing and bushing surfaces should not be assembled dry; coat them with plenty of clean oil first.
- Check the bearing surface: if there is discoloration, scratches or crushing, do not assemble until the bearing is renewed.
- Prepare the seal areas: remove old seal residue, and fit the new elements in the correct direction.
- Align with a tool: the drive gear or pulley should be aligned with suitable tools, not with heavy hammer blows.
- Check manual rotation: if the crankshaft does not turn freely by hand after assembly, do not continue the installation.
- Check for leaks after starting: oil and air leaks should be looked for while the compressor is running.
Common faults and solutions
- Knocking and loud noise in the compressor: may be caused by bearing wear or shaft play; the solution is to check the bearing and bushing and, if needed, replace the complete crankshaft.
- Failure to build pressure: may be caused by worn seals or gaskets; the solution is to renew the sealing elements.
- Oil leak from the compressor: may be caused by worn seals or a blocked oil passage; the solution is to clean the passage and replace the elements.
- Vibration and unbalanced running: may be caused by shaft misalignment or drive faults; the solution is to check the connection points and alignment.
- High temperature and burnt oil smell: may be caused by insufficient lubrication or partial blockage of the oil passage; the solution is to clean the passage and check the oil level.
Frequently Asked Questions
What symptoms indicate that the air brake compressor crankshaft should be replaced?
If knocking in the compressor, irregular noise while rotating and a clear drop in pressure build-up are seen together, the crankshaft should be inspected. Scratches or wear on the shaft surface may mean replacement is needed. If oil leakage occurs with these symptoms, the bearings and seals should be checked first. If the symptoms alone are not enough, dismantling the compressor for an internal inspection gives a more reliable result.
Can only the bearing of the crankshaft be replaced?
If the bearings and bushings are worn but the shaft surface is sound, only these elements can be renewed. If there are scratches or ovality on the shaft surface, changing only the bearing will not solve the problem. In that case the shaft and bearing should be considered together.
Is the crankshaft responsible if there is oil and air leakage?
Not every leak originates from the crankshaft. Seals, gaskets and oil passages are also common causes. These elements should be checked first, and if the problem continues, the crankshaft should be inspected.
How is the system tested after replacing the air brake compressor crankshaft?
First check whether the crankshaft turns freely by hand. Then run the compressor briefly and look for oil and air leaks. If the pressure rise is regular and the sound is normal, the test can be considered complete.
Should the crankshaft be replaced together with the piston?
The decision should depend on the condition of the piston and connecting rod. If the crankshaft is sound, replacing it alone may be sufficient. If there is wear at the connection seats, it is safer to service them together.