Gear
All Gear products 80
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
Air Compressor, Gear
No products on this page match the filter.
What is an Air Compressor Gear?
An Air Compressor Gear is the gear on trucks and buses that transmits motion from the engine to the air brake compressor. The gear turns on the compressor crankshaft and drives the pistons, producing compressed air. The air is sent to the air tank and feeds the brake circuits, suspension air bags and other pneumatic systems. In the workshop, this part is also known as a compressor gear or crank gear. The parts that wear out most are the gear teeth, shaft connection and bearing points; tooth breakage and increasing backlash occur most often in these areas. This page covers the single gear part only; the gear set is a separate category.
How does an Air Compressor Gear work and what does it include?
With the engine running, the gear connects to the compressor drive end and passes rotation to the crankshaft. This motion is converted into the suction and compression cycle through the connecting rod and piston, and the air is compressed inside the compressor body before being sent to the air tank. For the gear to work properly, the following parts must work together correctly:
- Gear teeth: the section that contacts the mating gear and carries the motion; pitting and breakage appear here.
- Hub and keyway: the section that attaches the gear to the shaft and prevents it from slipping.
- Pin and locking parts: keep the gear fixed on the shaft; a loose connection causes impact and noise.
- Bearing and bush: support the shaft rotation; if play develops, the gear moves off its axis.
- Oil seal: prevents oil from leaking out and dust from getting in.
Air Compressor Gear types
- Spur gear: a simple type with teeth parallel to the shaft axis; if the removed part is a spur gear, the same type must be selected.
- Helical gear: its angled teeth engage more smoothly; the tooth angle should be checked against the old part.
- Keyed gear: attached to the shaft with a key; the condition of the keyway should be inspected before fitting.
- Pinned gear: fixed to the shaft with a pin; the alignment of the pin holes must be considered when selecting.
How to choose the right Air Compressor Gear?
Selection should be based on the removed gear itself. The tooth type, shaft connection method, hub design and surface condition should be compared. The engine and compressor type that the compressor is connected to also affect the choice. On brands such as Mercedes-Benz, MAN, Scania, Volvo and DAF, different layouts can exist even within the same model series, so selecting by model name alone is a mistake.
| Criterion | What to check | Why it matters |
|---|---|---|
| Tooth profile | Tooth type, tooth angle, tooth direction | A mismatched tooth cannot mesh with the mating gear and wears quickly. |
| Shaft connection | Keyway and pin hole | A loose connection causes the gear to slip and creates impact. |
| Surface condition | Pitting, scoring, cracks, burn marks | A damaged surface produces noise and vibration. |
| Bearing fit | Play in the bearing and bush seat | Play causes axial movement of the gear. |
| Lubrication condition | Oil traces, seal seat, leakage | Running without oil wears the teeth out quickly. |
Installation and maintenance tips
- Lubrication: the gear and bearing surfaces should be lightly oiled with compressor oil before fitting.
- Tooth alignment: the contact pattern of the meshing gear pair should be checked; it must not be forced into place.
- Key and pin check: keys and pins must seat fully; any broken or loose part should be replaced.
- Seal fitting direction: the oil seal must be fitted in the correct direction, with its lip facing the oil side.
- Tightening sequence: nuts should be tightened in a cross pattern with even force, then rotation should be checked for smoothness.
Common faults and fixes
- Knocking and noise from the compressor: tooth wear or bearing play; the gear and bearings are checked and renewed.
- Pressure drop and slow brake circuit filling: the gear slips or a key breaks, so the compressor cannot turn regularly; connection points are secured and the broken part is replaced.
- Overheating of the compressor body: running without oil or a leaking oil seal; lubrication is corrected and the seal is renewed.
- Oil leakage and oil traces: seal wear or an incorrectly fitted seal; the seal is replaced and its seat cleaned.
Frequently Asked Questions
Which symptoms show that a compressor gear is worn?
Irregular knocking from the compressor body, increasing vibration and slower air build-up are the most common symptoms. If pressure rise is delayed, the gear and bearing points should be checked.
Does a pressure drop always come from the gear?
No. For a pressure drop, air leaks, valves and piston rings should be checked first. The gear can affect pressure build-up, but another part may be the root cause.
Should other parts be checked when replacing the gear?
Yes, the bearing, bush, key and oil seal on the same shaft should be checked together. A worn bearing can cause the new gear to fail in a short time.
Why is lubrication so important?
Oil forms a film between the gear surfaces, which reduces wear and helps dissipate heat. Running without oil or with dirty oil damages the tooth surfaces quickly.
How can compressor gear noise be told apart from other noise?
Noise from the gear is usually a regular knocking that changes with movement. Bearing noise appears as a constant hum, while connecting rod noise can sound like an impact knock. The source should be identified during controlled running.