Housing
All Housing products 205
No products on this page match the filter.
What is an air brake compressor housing?
The air brake compressor housing is the main structure of the compressor that produces compressed air in the air brake system of trucks, buses and trailers. It carries the cylinder block, crankcase and bearing seats. Its role is to guide the piston's movement, hold the oil and carry the valve group. The integrity of the housing directly affects the compressor's ability to build pressure. The parts that actually wear are the cylinder bore and the bearing seats; a scored cylinder leaks air and lowers compressor efficiency. In the field it is also called the "compressor casing" or "compressor block".
How does an air brake compressor housing work and what does it include?
The housing is the body that holds the moving parts of the compressor together and contains the passages the oil flows through. It includes the following sections:
- Cylinder block: the main bore in which the piston moves and the air is compressed.
- Cylinder liner: on some types, a separate liner forms the inner surface of the cylinder.
- Crankcase: the section where the crank mechanism is lubricated and which closes off the lower part.
- Main bearing seats: the seats in which the crankshaft and bushings sit.
- Oil galleries: the internal passages that carry oil from the crankcase to the bearing and piston areas.
- Head mating surface: the flat surface on which the valve assembly and head sit with a gasket.
Types of air brake compressor housings
- Single-cylinder housing: it carries one cylinder block, so it is used on small-displacement compressors.
- Twin-cylinder housing: it has two cylinder bores and a shared crankcase, so it is chosen according to the air capacity required.
- Air-cooled housing: it has cooling fins that dissipate heat and is cooled by airflow.
- Water-cooled housing: it has internal passages for coolant and is connected to the engine cooling circuit.
How to choose the right air brake compressor housing
To find the right housing, the casting code of the removed compressor, the head mounting pattern and the cylinder layout should be checked together. Going by outward appearance alone is misleading, because housings that look alike can have different mounting holes and oil passages. Brands such as Mercedes-Benz, MAN, Scania, Volvo and DAF can use different layouts even within the same model series, so choosing by model name alone is a mistake. The safest method is to use the removed part as a reference together with its mating surfaces. Even when the mating surfaces of the housing are sound, the condition of the internal passages must be checked separately.
| Criterion | What to check | Why it matters |
|---|---|---|
| Casting code | Cast and stamped markings on the housing | Housings that look alike on the outside can differ |
| Cylinder layout | Whether it is single-cylinder or twin-cylinder | The cylinder block determines the capacity |
| Head mating surface | Layout of the bolt holes and the gasket seat | The valve assembly only seats correctly if this matches |
| Cooling type | Finned design or water passages | The wrong type of housing causes overheating |
| Surface condition | Scoring, cracks or breaks in the cylinder and bearing seats | A damaged housing ruins the new parts as well |
Fitting and maintenance tips
- Oil galleries: clean the passages before fitting; a blocked passage leaves the bearings without oil.
- Cylinder surface: if there is scoring, honing (a process that restores the cylinder bore surface) may be needed; a rough surface is harmful to the rings and piston.
- Gasket surfaces: the head and crankcase mating surfaces must be flat, and a new gasket must not be fitted until old gasket residue has been scraped off.
- Crack check: inspect the housing visually before fitting and, if needed, confirm with a leak test.
- Threaded holes: do not bolt on the head until holes with damaged threads have been repaired, because a loose joint increases air leakage.
Common faults and solutions
- Air leak under the head: the head mating surface may be warped or the gasket seat damaged; the surface should be corrected and a new gasket fitted.
- Leaking sound and pressure drop at the cylinder: the cylinder bore may be scored; the surface should be repaired or the liner renewed.
- Rising oil level or oil leak at the crankcase: an oil gallery may be blocked or the crankcase gasket may have failed; the galleries should be cleared and the gasket renewed.
- Overheating of the housing: the cooling fins may be dirty or the water passages blocked; cleaning is needed.
- Crack in the housing: it can result from freezing, overheating or impact; if there is a crack, the housing should be replaced with a new one.
Frequently Asked Questions
Can a crack in the housing be repaired?
Small cracks can be assessed by a specialist workshop. A crack in the cylinder block or a bearing seat, however, is not acceptable for safety reasons and the housing must be replaced. The location of the crack is important in deciding whether the housing is still usable. A repaired housing should not be put back into service before it passes a leak test.
Should the valve assembly be renewed when the housing is replaced?
If the head mounting is compatible, the old valve assembly can be reused; however, the wear of the valves must be checked carefully. If the head mating surface and gasket seat do not match the new housing, the valve assembly should be renewed as well.
How can you tell that an oil gallery in the housing is blocked?
Heat in the bearing area, oil loss in the crankcase or unusual noise can be signs of a blockage. The passage should be cleaned through the housing and the flow checked. Even if the passage looks open, the flow through the internal channels must be checked separately. Do not proceed to fitting until the blockage has been cleared.
What is the difference between buying a housing and buying a complete compressor?
The housing covers only the main structure; the piston, crankshaft and valve group must be supplied separately. A complete compressor includes all the necessary internal parts. Deciding without establishing which parts of the removed unit are still sound can lead to a wrong decision. This difference is hard to judge before dismantling if the part has not been compared.
Why is the casting code on the housing important?
The casting code is the most reliable indication of which compressor type the housing belongs to. Even when the outward appearance is similar, the mating surfaces and oil passages can differ. If the code cannot be read, a photo of the removed part and its mating surfaces should be assessed together.