Pin
All Pin products 75
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
Brake Caliper Pin, Pin
No products on this page match the filter.
What is an Air Disc Brake Caliper Pin?
An Air Disc Brake Caliper Pin is a cylindrical guide pin in the disc brake system of heavy commercial vehicles. It lets the caliper slide freely on its carrier so the caliper can press the pads evenly against the brake disc. Its job is to let the caliper move smoothly in both directions and return cleanly. Over time, the parts that wear most are the pin body, the pin bushing and the bushing contact surface. In the trade it is also known as a caliper slide pin or caliper guide pin.
How does the Air Disc Brake Caliper Pin work and what parts does it include?
Each time the caliper moves the pads toward and away from the disc, the pin slides along its own axis. For this movement to happen without binding, the bushing, dust boot, seal and bore work together. The main parts of the assembly are:
- Pin body: The main cylindrical part that attaches the caliper to the carrier and guides its sliding motion.
- Pin bushing: The bushing that reduces friction between the pin and its bore and protects the contact surface.
- Dust boot: The protective rubber boot that keeps road dust, mud and water out of the pin bore.
- Seal, gasket and O-ring: Seals that keep dirt and moisture from entering the pin bore.
- Pin and retaining parts: On some designs, the pin and retaining parts that hold the pin in its bore.
- Carrier bore: The seat where the pin sits and that guides the caliper sliding motion.
Air Disc Brake Caliper Pin types
- Single pin: Preferred when only one pin is worn; if the other pin is sound, a single part is enough.
- Axle set: Preferred when the pins on both sides of an axle need replacing together, so wear stays balanced.
- Complete pin kit: Suitable when the bore shows wear or the whole assembly is being renewed, since the pin, bushing, dust boot and seal come together.
How to choose the right Air Disc Brake Caliper Pin
The most reliable method is to check the removed pin together with the condition of the bore and bushing. Then check the brake system type, the caliper model and the carrier design. On brands such as Mercedes-Benz, MAN, Scania, Volvo and DAF, different layouts can exist even within the same model series, so choosing by model name alone is a mistake.
| Criterion | What to check | Why it matters |
|---|---|---|
| Removed pin | Shape, head design and fit in the bore | A pin that does not fit holds the caliper unevenly |
| Caliper model | Carrier type and caliper body structure | The same pin may not fit a different carrier |
| Bushing and dust boot | Material type and cross-section | A mismatched bushing increases friction |
| Surface coating | Anti-corrosion coating and surface smoothness | Rust makes the pin hard to slide |
Installation and maintenance points
- Bore cleaning: Before fitting the new pin, clean the bore and carrier seat of dirt, rust and old gasket residue.
- Bushing lubrication: Lightly grease the bushing and pin contact surface with a suitable grease; excess grease attracts dust and speeds up wear.
- Dust boot seating: The boot must sit fully in its groove, fitted without folds or tears.
- Pin and retainer check: After assembly, check again that the pin is held in place by the pin and retaining parts.
- Sliding test: After installing the caliper, slide it by hand to check for binding; if it binds, repeat the installation.
Common faults and fixes
- Caliper does not return: Likely caused by hardening and dirt build-up in the pin bushing; clean and grease the bushing and pin, and replace the bushing if needed.
- Uneven pad wear on one side: Likely caused by binding in the pin bore or one-sided friction; check the pin and bore and restore free movement.
- Delayed braking and uneven pull: A seized caliper, combined with a pressure drop, pulls the vehicle to one side; remove the caliper and replace the pin.
- Torn boot and dust ingress: A torn dust boot wears out the pin bore; replace the boot, clean the bore and fit a new seal.
- Rust and pitting in the bore: Pitting on the carrier surface prevents the pin from seating; if the damage cannot be repaired, replace the carrier.
Frequently Asked Questions
When should the Air Disc Brake Caliper Pin be replaced?
The pin should be replaced if the caliper no longer slides, the bushing is worn or the dust boot is torn. One-sided pad wear can also point to a pin problem. Replacement is recommended if marks or rust are visible in the bore during removal.
Should the pin be replaced alone or as a set?
If only one pin has a problem, a single part is enough. If the bushing and dust boot are also worn, a complete kit gives a more reliable result. Where regular axle-based maintenance is done, replacing both sides together is preferred.
Does the pin need lubrication?
Yes, lightly greasing the bushing and pin contact surface makes sliding easier. Too much grease attracts dust and sand and speeds up wear. Keep the amount small and wipe off any excess.
Can the pin be fitted without a dust boot?
An unprotected pin bore wears quickly from dirt and moisture, and a pin fitted without a boot can bind within a short time. The boot should be fitted or replaced with every pin change.
What should be checked if the pin does not slide?
First check the bore and bushing for dirt, rust and dryness. Check that the pin and retaining parts are in place. If the problem continues, check the carrier bore for pitting.