Release Bearing
Subcategories
1Other Release Bearing products 5
Products not assigned to any subcategory
No products on this page match the filter.
What is a clutch release bearing?
A clutch release bearing is a heavy commercial vehicle part that transfers pedal movement to the pressure plate assembly and temporarily interrupts engine power during gear changes. Its role is to contact the fingers of the pressure plate when the pedal is pressed, moving the diaphragm and pulling the pressure plate away from the flywheel. In service, the part that wears most is the point where the bearing contacts the rotating surface, since constant friction and rotation gradually wear it down. In the trade it is also known as a throw-out bearing or clutch bearing.
How does a clutch release bearing work and what parts does it include?
The bearing works as the moving part of the clutch mechanism between the pressure plate assembly and the pedal linkage. The following parts work together to keep the bearing functioning correctly.
- Pressure plate fingers: the contact points the bearing presses against, which move the diaphragm.
- Pressure plate: the part that clamps the clutch disc against the flywheel and, when released, lets the gear move freely.
- Clutch disc: the friction part clamped between the flywheel and pressure plate to transmit power.
- Flywheel: the rotating part that carries engine rotation to the clutch.
- Guide bushing and bearing housing components: they allow the bearing to slide smoothly on the guide tube.
- Spring and bearing group: supports the bearing in its correct position and smooth, low-friction rotation.
Types of clutch release bearing
- Hydraulic system bearing: preferred in clutch systems that transmit pedal movement through hydraulic pressure.
- Mechanical system bearing: used in layouts that transmit pedal movement through a fork and linkage rod.
- Bearing-type release bearing: its rotating surface runs on a ball bearing, so friction is low and it suits heavy gear shifting use.
- Complete set: the housing, bearing and spring group come together, so it is preferred when replacing everything at once.
- Single bearing: suitable only when the bearing itself is worn and the other clutch parts are in sound condition.
How to choose the correct clutch release bearing
Selection should be made by considering the reference on the removed part, the housing shape and the type of clutch system (hydraulic or mechanical). In brands such as Mercedes-Benz, MAN, Scania, Volvo and DAF, different layouts can exist even within the same model series, so selecting by model name alone is a mistake. Gearbox design and guide tube geometry are among the most decisive factors for a correct match.
| Criterion | What to check | Why it matters |
|---|---|---|
| System type | Hydraulic or mechanical pedal linkage | Determines how the bearing operates |
| Removed part | Markings, reference and housing shape | A wrong match causes harsh gear engagement |
| Gearbox design | Guide tube geometry | Ensures the bearing seats correctly |
| Housing body | Whether the bearing and spring group come together | A missing part shortens service life |
| Bearing housing parts | Guide bushing and bearing condition | Affects friction and noise |
| Usage pattern | Condition of the other clutch parts | Balances parts cost and labour time |
Installation and maintenance points
- Assess the whole system: if the clutch disc, pressure plate and flywheel are worn, replacing them together with the bearing prevents a repeat failure in a short time.
- Clean the guide bushing: old dirt and dried grease must be removed before fitting a new bearing.
- Use the correct grease: lubricate only the specified points; excess grease attracts dust and sand and increases friction.
- Check the bearing orientation: the seating surface and direction of the part must be checked before fitting.
- Verify pedal adjustment: if the adjustment is wrong, the bearing stays in constant contact and wears early.
- Inspect the guide tube: if burrs or scratches are present, the bearing binds, so the surfaces must be smooth.
Common faults and solutions
- Squeal when shifting gears: the bearing has dried out or worn; lubricate the guide bushing or replace the bearing.
- Heavy pedal: friction or incorrect seating in the guide tube; clean the tube and check bearing seating.
- Slipping and incomplete power transfer: wear of the clutch disc and pressure plate; assess the system together with the bearing.
- Constant noise or vibration: noise from the rotating bearing even with the pedal released; the bearing needs replacing.
- Hard gear engagement: wrong reference or incorrect fitting; choose the correct part and repeat the fitting.
Frequently Asked Questions
When should a clutch release bearing be replaced?
The bearing should be checked when a squeal during gear changes, a change in pedal effort or constant noise is noticed. Replacement should not be delayed once signs of wear appear. Assessing it together with the other system parts is the most sound approach.
Should the clutch release bearing be replaced together with the clutch disc?
If the clutch disc or pressure plate is worn, it is recommended to check the bearing and replace it together. This balances the service life of the system and prevents repeat labour in a short time. Replacing only the bearing can be enough if only the bearing is worn.
Can a hydraulic and a mechanical system bearing be used interchangeably?
No, a bearing that does not match the operating system does not provide the correct contact point. The removed part and the vehicle's pedal linkage must always be checked. If in doubt, selecting by reference is the safest route.
Why does a clutch release bearing make noise?
The most common cause is reduced lubrication on the rotating surface or bearing wear. Dirt and moisture also increase noise. If the noise continues, the part should be removed and inspected.
What should be checked on the removed bearing?
The markings, housing shape and condition of the rotating surface are the first things to check. If there are scratches, colour change or a loose bearing, the part must be replaced. The complete removed part should be used as reference to confirm the match.