A semi truck pulls to one side when braking, or one wheel runs hot, because the two wheels on an axle are not producing equal braking force or one wheel is not fully releasing. First work out whether the symptom sits at one wheel, one axle or the whole vehicle. Then check the guide pin and bush, dust boot, caliper mechanism, actuating lever, brake chamber and ALB valve in turn.
In short:
- Pulling under braking and a brake that drags and overheats are two separate symptom families, and each is tracked on its own.
- A problem at one wheel usually points to that wheel's caliper, while two wheels on the same axle heating together points to the axle circuit.
- The ALB valve changes the total braking force on the rear axle, but it does not explain a left to right difference on its own.
- A wheel that smokes, smells of burning or keeps overheating must not be driven on.
Why a semi truck pulls to one side when braking: where does the fault start?
Pulling usually starts at one wheel or one axle, and the way the circuit works shows where to look. Air from the brake pedal (treadle) valve fills the brake chamber on the axle. The chamber pushrod moves the caliper's actuating lever, and the caliper mechanism presses the pads against the disc. When the pedal is released and the air exhausts, the return springs pull the mechanism back and the pads clear the disc.
Terminology note: the brake chamber (also called the service chamber) is the air-operated actuator that pushes the lever. The dust boot is the rubber cover on the caliper that keeps dirt and water away from the guide pin and mechanism. They are two different parts and should not be mixed up when ordering.
Rule out non-brake causes first. A tyre pressure difference between left and right, unevenly worn tyres, wheel alignment out of tolerance, a broken leaf spring, a deflated air spring (airbag) or loose axle mounts can all make a lorry drift under braking. Set tyre pressure to the tyre maker's load and pressure table, check alignment and suspension, and move on to the brakes only if the pull remains.
Which wheel and which axle is the symptom pointing to?
Deciding whether the symptom sits at wheel, axle or vehicle level narrows down the fault considerably. A truck steers towards the side with more braking force, and a dragging wheel can pull it towards its own side. The table matches the most common cases to parts.
| Symptom | Likely cause | Check | Action |
|---|---|---|---|
| Steering pulls one way under braking | One front caliper applies weaker or later: seized guide pin, sticking mechanism, air hose or brake chamber problem | Compare pad wear and post-drive heat of the two front wheels | Check the caliper, air hose and brake chamber on the weak or dragging side |
| Burning smell, smoke or overheating at one wheel | That wheel is not releasing | With the axle raised, spin the wheel by hand and watch whether the actuating lever returns after braking | Check guide pin and bush, mechanism and chamber pushrod |
| Both wheels on the same axle run hot | Air exhausts late on that axle circuit, or the brake stays partly applied | Check exhaust at that axle's relay valve after the pedal is released | Valve diagnosis (see the treadle and relay valve article) |
| All wheels release late | Treadle valve or main circuit | Listen for the exhaust when the pedal is released and compare release between axles | Treadle valve diagnosis |
| Rear wheels lock easily when empty, rear brakes weak when loaded | ALB setting or linkage | ALB lever, joint and setting plate | ALB check (see the ALB section) |
| Only trailer wheels run hot | Trailer brake circuit | Trailer brake valve and line | Treat the trailer circuit separately |
For axle-by-axle late release and valve faults, see the treadle and relay valve diagnosis article. On vehicles with EBS or ABS, read the fault memory with a diagnostic tool when the complaint is a pull. This article focuses on air disc brakes; on drum brakes, a slack adjuster that has lost its adjustment can cause the same pull.
How do you check a hot wheel safely?
If one wheel is suspected of overheating, compare the two wheels on the same axle and do not skip the safety steps.
Safety: Park on level ground, chock the wheels and switch off the engine. Do not touch a hot disc, caliper or rim with bare hands; let them cool. Do not open the spring brake section of the brake chamber, because the spring inside carries a very high force. A raised axle must sit on axle stands, never on a jack alone, and lifting an axle or working under the vehicle is a job for trained staff.
- 1. After a drive, measure the wheels with a non-contact thermometer, or compare the hub and rim areas by eye.
- 2. Look for rim discolouration, heavy brake dust, a burning smell and rubbing noise.
- 3. With the other axles chocked, put the raised axle on stands, release the parking brake and, with the system charged, turn the wheel by hand. If it turns heavily or rubs compared with the opposite side, that caliper has a fault.
- 4. Have a helper apply and release the brake while you watch the actuating lever and the pushrod return fully.
- 5. When the pads are removed, note any wear difference between the inner and outer pad.
Uneven inner and outer pad wear suggests the caliper cannot slide on its pins; the causes are covered in the article on why a caliper seizes. A brake that drags continuously also raises fuel consumption on top of the heat.
Guide pins, bushes and dust boot: when the caliper cannot slide
On a sliding air disc brake caliper, the body slides on its guide pins so that both pads press on the disc evenly; if a pin or bush seizes, one pad presses harder than the other, or does not leave the disc at all. The result is a weak brake or constant drag and heat at that wheel. The caliper guide pin is the pin that lets the caliper body slide along its axis on the carrier.
With the pads removed, push the caliper body back and forth by hand on its pins; it should slide smoothly without catching. Look for play, binding and rust on the pin, and ovalling or tearing in the bush. Permitted play comes from the manufacturer's service documentation.
The dust boot does not cause a pull itself, but once it tears or slips off, water, road salt and dirt reach the pin and the mechanism. That is why an old torn boot is often behind a pull or overheating complaint. Check the boot for cracks, tears, hardening and displacement.
If a seized pin is found, replace the pin, bush and boot together; fitting only a new boot does not rescue a rusted pin. The right caliper guide pin and bush kits are chosen by caliper type and number.
Mechanism, actuating lever and brake chamber: when the brake does not release
If a wheel keeps heating and the caliper slides freely on its pins, the fault is most often in the mechanism that should pull the pads back, in the actuating lever, or in the brake chamber that pushes the lever.
The caliper mechanism is the internal assembly that passes force from the actuating lever to the pads through the pushing elements, and that holds the return springs and the automatic adjuster closing up the clearance as the pads wear. If water or dirt gets in, the pushing elements do not return or the automatic adjuster over-adjusts; the pads rest on the disc and the wheel heats up. In that case match the caliper adjuster mechanisms and repair kits to the caliper number.
The actuating lever is the lever that the chamber pushrod presses and that transfers the force to the mechanism. If the lever or its bearing rusts and binds, the mechanism does not come back; the catalogue lists this part separately as the operating lever.
If the service section of the brake chamber does not exhaust fully, or the pushrod does not return, the lever stays applied. A spring section that does not fully release gives the same symptom, but that is a separate parking brake fault.
To separate them, remove the brake chamber from the caliper following the manufacturer's instructions, after caging the spring brake with the caging bolt as instructed and releasing the pressure in the line. Then move the actuating lever by hand. If the lever swings freely, the fault is in the chamber or the valve side; if it is stiff or does not return, the fault is inside the caliper. Clearances and check values come from the manufacturer's service documentation.
Axle balance: what does an ALB valve change, and what does it not change?
The ALB (automatic load-sensing) valve is a pneumatic valve that adjusts the air pressure going to the brake chambers of the rear axle according to its load. Because it acts on both sides of an axle together, it cannot explain a left to right difference; it changes the balance between the front and rear axles and how the vehicle brakes empty or loaded.
Typical ALB faults show up as rear wheels locking early when empty, a weak rear brake when loaded, or noticeably different pad wear and heat on the rear axle compared with the front. Things to check:
- The rod and joint linking the valve to the axle: they should not be broken, bent or worn.
- The valve lever should move freely without sticking.
- There should be no air leak noise from the valve body or fittings.
- The ALB plate on the vehicle should be in place and legible.
Adjustment is done in a workshop with suitable test equipment, strictly to that plate and the manufacturer's service documentation. For a valve that leaks at the body or has an internal fault, pick the part that matches the old valve number from the ALB load sensing valves. On many EBS vehicles load sensing is electronic and there may be no mechanical ALB valve. The effect of a left to right difference and the ALB on the roller brake test at the roadworthiness inspection belongs in a separate brake test article.
When should you go to a workshop, and what is checked after the repair?
A wheel that smokes, smells of burning or keeps overheating must not be driven on; stop the vehicle somewhere safe and call for service. An overheated brake loses braking power and puts the tyre, wheel hub and bearing at risk.
- 1. Work on both sides of the same axle together, because a new part fitted on one side only can create a new imbalance.
- 2. After a short test drive, compare the wheels again.
- 3. If the pull continues, review tyre pressure, alignment and suspension again.
The decision between a repair kit and a complete caliper is covered in the caliper article linked above. For a complete replacement, when choosing among air disc brake calipers, check the label or OEM number on the caliper, the chassis number (VIN), left or right side, axle position and model year together. In the MPT catalogue, searching by OEM number makes it easier to match the caliper and its parts.