Trailer Height Adjustment Valve

Products: 2

Trailer Height Control Valve is a brake system part that balances the distance between chassis and axle according to load on air-suspended trailers. Read the guide

All Trailer Height Adjustment Valve products 2

What is a Trailer Height Control Valve?

A Trailer Height Control Valve is a control part within the brake system group on air-suspended trailers. It keeps the distance between the chassis and the axle constant according to the load by regulating the air flowing to and from the air bellows. Its place in the brake group is due to the fact that the amount of air reaching the bellows indirectly affects brake distribution between axles. In workshops it is also known as a leveling valve or ride height valve. Over time, the part that wears most is the moving shaft inside the valve and the seal and o-ring set around it. When these harden, air leaks begin and the trailer either sinks under load or rises too high when empty.

How does a Trailer Height Control Valve work and what parts does it include?

The valve is a directional unit that sends air pressure from the trailer's air tank to the suspension bellows, or vents air from the bellows. The following parts work together for correct operation.

  • Body: The outer shell of the valve. It houses the internal air passages and inlets and provides the mounting point on the trailer chassis.
  • Control lever and linkage rod: Transfers the movement from the axle to the valve's internal mechanism. The lever senses changes in ride height.
  • Spool and sleeve: The moving element that opens and closes the air path. This part decides when to raise or lower the trailer.
  • Seal and o-ring set: Prevents air leakage around the shaft. Hardening is the most common cause of failure.
  • Exhaust port: The passage that vents excess air from the bellows to the atmosphere. A blocked exhaust causes the trailer to rise.
  • Air hose fittings and nipples: Connect the air tank and bellows to the valve. A loose or cracked fitting is the main source of hissing leak noise.

Trailer Height Control Valve types

  • Lever-operated mechanical type: Operated through a linkage arm connected to the axle. It is the most common classic type on air-suspended trailers.
  • Electronically controlled type: Manages ride height values through sensors and an electronic control unit. It requires cable connections.
  • Bolt-on mounting type: Fixed to the chassis with bolts. It must match the existing bracket holes.

How to choose the correct Trailer Height Control Valve?

The most reliable method is to note the markings on the body of the removed valve, the lever connection type and the position of the air inlets. The connection points, lever linkage and mounting bracket of the existing valve must match the new part exactly. The trailer manufacturer, axle brand and system type also determine the choice. Even within the same model series, different layouts can exist, so choosing by model name alone is a mistake.

CriterionWhat to checkWhy it matters
System typeThe trailer's air suspension layout and bellows lineA valve with the wrong layout disrupts air distribution
Body markingsRecords and codes on the removed partThis information is the fastest route to an accurate match
Lever and linkageConnection type and direction of the lever on the axleHeight sensing depends on this connection
Air inlet and exhaustFitting layout, outlet direction and hose typeDetermines leak and blockage risk
Mounting bracketHole pattern and mounting point on the chassisThe valve must sit without shifting its axis
Electrical connectionCable connector and sensor compatibility (electronic type)Incorrect wiring triggers a system warning

Installation and maintenance guidelines

  • Bleed the air system: Fully drain the pressure from the air tank before installation. Removing a body under pressure is dangerous.
  • Prepare the seals: Lubricate new seal and o-ring parts with suitable grease, do not install them dry, and check that they are not cut.
  • Set the lever: With the trailer empty and loaded, check the ride height and adjust the lever connection according to the manufacturer's reference.
  • Tighten the fittings: Tighten air hose connections without overtightening. Replace cracked or hardened hoses.
  • Check for leaks: After installation, apply a mixture of soap and water to the connection points and watch for foam.

Common faults and their solutions

  • Trailer sinks under load: The likely cause is an air leak on the inlet side or hardening of the seal inside the valve. The solution is replacing the seal and o-ring set and leak testing the connections.
  • Trailer rises too high when empty: The likely cause is a blocked exhaust port or a slipped lever linkage. The solution is cleaning the exhaust passage and readjusting the lever.
  • Constant hissing leak noise: The likely cause is loose fittings or a cracked body. The solution is tightening the connections and replacing the cracked body.
  • Uneven ride height side to side: The likely cause is that the left and right bellows lines receive different pressures. The solution is checking the valve and lines together and replacing the valve if necessary.

Frequently Asked Questions

How does a faulty Trailer Height Control Valve show itself on the trailer?

The most common sign is one side of the trailer sitting lower than the other, or constantly sinking when loaded. A leak sound from the bellows and delayed height changes are also frequent. Because this can indirectly affect brake balance, the symptoms should be checked as soon as they are noticed.

Is it possible to replace only the seal of the valve?

In most cases the seal and o-ring set is available separately, so only the seal group can be replaced. However, if the body is cracked or the spool bore is worn, replacing the seals will not be a lasting fix. First determine which part of the valve the leak comes from.

Should a valve be repaired or replaced?

If the body is sound and only the seal or o-ring is worn, internal repair may be enough. If the body is cracked, the lever is broken or the bore is badly worn, replacement is the safer option. The overall condition of the trailer should also be considered when deciding.

How is ride height checked after replacing the valve?

Ride height should be measured and recorded with the trailer both empty and loaded. Once air pressure has settled, the bellows should be seen to inflate evenly. A leak test should also be carried out on all connections during the check.

Does this valve count as a brake system fault?

It is not a direct fault of the brake control valve or the brake caliper, but it can indirectly affect how braking force is distributed between axles. If there is an air leak, brake pressure may also drop, so the vehicle should be checked before going back on the road.

Press Enter to search the full catalogue

Request a quote

Your email app opens with the request filled in.