Visco Drive
All Visco Drive products 201
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
Fan, Visco Drive
No products on this page match the filter.
What is a cooling fan hub with studs?
A cooling fan hub with studs is the centre part of the fan assembly on trucks and buses, connecting the fan to the drive side. It holds the fan blade set and passes the rotation force to the fan, working at the point where the blades are fixed and supporting the air flow through the radiator that keeps engine temperature under control. In the workshop this part is also called the fan boss or fan flange. The part that wears and fatigues most is the set of holes where the studs sit and the joint between the hub and the body, since vibration gradually loosens these points.
How does a cooling fan hub with studs work and which parts does it include?
A cooling fan hub with studs is the central connecting element of the fan assembly. It takes the rotation from the drive source, namely the belt pulley or viscous clutch, and carries it to the fan blade set. For this reason every connection point on it must be both strong and aligned. The main components surrounding this hub, considered together, are:
- Hub body: the main centre part that carries the fan blade set and passes the rotation to the fan.
- Studs: fix the hub to the drive-side flange and keep the connection tight.
- Centre bore and seat: the section where the drive shaft or flange sits, and it sets the alignment.
- Blade mounting face: the plane where the fan blades are held with studs and nuts.
- Lock washers and nuts: fasteners that prevent the studs from loosening over time.
Types of Cooling Fan Hub with Studs
- Complete hub: a full set supplied with its studs and fasteners, preferred when the hub needs to be replaced as a whole.
- Hub body only: used when only the body is worn while the studs and flange are sound.
- Belt-driven fit: for fan layouts driven by a belt pulley, a hub that can be aligned with the pulley is needed.
- Viscous clutch compatible type: the hub selected for a fan layout working with a viscous clutch, with a mounting face that matches it.
How to Choose the Right Cooling Fan Hub with Studs
The safest way to choose is to use the removed hub as the reference. The stud layout, centre bore, flange face and drive type of the old part should be compared directly with the new one. The type of engine and fan drive system should also be considered, and fit should be checked together with OE-equivalent quality. Even within the same model series, brands such as Mercedes-Benz, MAN, Scania, Volvo and DAF can have different layouts, so choosing by model name alone is a mistake.
| Criterion | What to check | Why it matters |
|---|---|---|
| Stud layout | Whether the position and spacing of the studs match the old part | A wrong layout stops the hub from seating on the flange |
| Centre bore | Fit of the seat on the drive side | A misaligned hub causes vibration |
| Mounting face | Flatness of the flange and blade surface | An uneven face loosens the joint over time |
| Drive type | Belt or viscous clutch layout | A hub that does not match the type will not seat on the drive system |
| Cracks and wear | Cracks or deformation in the hub body | A fatigued part carries a risk of breaking |
Assembly and maintenance points
- Stud connection: studs should be tightened in a crossing sequence with even force; a connection loaded at one point strains the hub.
- Surface cleaning: rust, dirt and old residue on the flange and hub surface must be cleaned before fitting.
- Locking parts: use a lock washer or new nut, and do not refit the old locking part.
- Rotation check: after fitting, turn the fan by hand to check for friction or binding.
- Vibration monitoring: if abnormal shaking appears on first run, stop the engine and recheck the connections.
Common faults and solutions
- Shaking and noise in the fan: the hub studs have loosened or the hub is misaligned; tighten the studs and recheck the alignment.
- Stud breakage or pulling out of the seat: overload and fatigue; replace the stud with a new one and check the connection face.
- Crack in the hub body: fatigue and vibration; a cracked hub must be replaced with a new one.
- Friction when the fan turns: the connection is bent or the blades touch the surroundings; check the connection angle and blade clearance.
Frequently Asked Questions
Will a removed cooling fan hub with studs fit a new one exactly?
Fit depends on the stud layout, centre bore and drive type. Before fitting the new part, check that these three points match the removed part. If you are unsure, the most reliable approach is to take the removed part along and compare them.
Can the studs be reused in their old condition?
If the studs show stretching, rounded corners or damaged threads, they must not be reused. Even studs that look sound may be fatigued, so fitting new fasteners is safer. Locking parts should also be renewed at every assembly.
Can only the hub be replaced if the blades are sound?
A hub fault may be independent of the blade condition, but the blade mounting face and balance should be checked before replacement. If the blades are damaged, replacing only the hub will not solve the problem. This check should be made during removal.
How should the first check be done after fitting a new hub?
First, with the engine off, turn the fan by hand and check for friction. Then run the engine briefly and listen for abnormal shaking and noise. If any vibration is noticed, retighten the connections.
Why is the drive type so important in choosing?
A fan layout driven by a belt pulley and one using a viscous clutch need different mounting faces. A hub that does not match the type cannot be fitted, or if forced on it will strain the drive system. For this reason the choice should always follow the drive layout of the fan.