Bushing
All Bushing products 12
Brake Caliper Mechanism, Bushing
Brake Caliper Mechanism, Bushing
Brake Caliper Mechanism, Bushing
Brake Caliper Mechanism, Bushing
Brake Caliper Mechanism, Bushing
Brake Caliper Mechanism, Bushing
Brake Caliper Mechanism, Bushing
Brake Caliper Mechanism, Bushing
Brake Caliper Mechanism, Bushing
Brake Caliper Mechanism, Bushing
Brake Caliper Mechanism, Bushing
No products on this page match the filter.
What is Air Disc Brake Caliper Mechanism Bushing?
Air Disc Brake Caliper Mechanism Bushing is the small bearing part inside the caliper housing that supports the moving assembly on its guide pins in pneumatic air brake systems, reducing friction so the caliper slides evenly. In the field it is also known as a caliper bushing or slide pin bushing. The part that actually wears is the surface the pin slides on; as wear grows the caliper body tilts, the pads no longer press the disc evenly and the lining wears quickly on one side. That makes the bushing a quiet but critical part of the caliper mechanism.
How does Air Disc Brake Caliper Mechanism Bushing work and which parts does it cover?
The bushing lets the caliper body move the pad toward and away from the disc with smooth sliding on the guide pin. This page covers bushings only; washers, seals and gaskets are listed in separate categories. The following parts work together in the assembly.
- Guide pin: the shaft that slides inside the bushing and directs the caliper body toward the pad.
- Dust boot: the rubber part that seals the pin against dust and water.
- Caliper housing bore: the machined seat in which the bushing sits.
- Grease: the lubricant that reduces friction between the pin and the bushing surface.
- Return spring: the spring that pulls the caliper and pad back when the brake is released.
Air Disc Brake Caliper Mechanism Bushing types
- Bronze bushing: preferred in heavy duty use where strength under high load and friction is needed.
- Composite (plastic based) bushing: needs less grease and runs quietly, preferred in light use.
- Single bushing: applied when only one bearing is worn and the other is still sound.
- Bushing set: both pin bearings are chosen together so the seats stay matched when both are renewed.
How to choose the right Air Disc Brake Caliper Mechanism Bushing?
Selection starts with the removed old bushing and the reference on the pin. Check the outer surface, the material appearance and the marks in the seat, and confirm the system type as well. Mercedes-Benz, MAN, Scania, Volvo and DAF can use different layouts even within the same model series, so choosing by model name alone is a mistake.
| Criterion | What to check | Why it matters |
|---|---|---|
| Old bushing material | Whether it is bronze or composite, surface finish and oil marks | Wrong material changes friction and lubrication |
| Pin seat | Scratches, rust and cleanliness of the seat in the housing | A worn seat lets the bushing move and it will not stay in place |
| System type | The axle and model group the caliper is used on | Parts that look alike can fit different housings |
| Renewal scope | Whether both pin bearings are worn together | If one bearing is renewed and the other is worn, the system stays unbalanced |
| Surface quality | Channels, burrs or dents on the inner surface | A rough surface grips the pin and the slide becomes intermittent |
Installation and maintenance points
- Clean the seat: rust, dirt and old grease must be fully removed before the new bushing is fitted.
- Use the correct grease: apply grease suited to the bushing and pin surface; excess grease collects dust inside the boot.
- Check the boot: a torn or hardened boot dirties the pin and bushing quickly, so replace them together.
- Check the pin by hand: after assembly, test that the pin slides freely without sticking.
- Tighten the mounting bolts in sequence: caliper bolts must be tightened to the manufacturer value and in the correct order.
Common faults and their solutions
- Caliper sticks on one side: the bushing is worn or its surface is scratched; renew the bushing, then clean and grease the pin.
- Braking is delayed and uneven: when the pin binds the pad does not fully release; check the bushing and pin seat.
- Slow return after braking: even when pressure returns to normal the pad does not retract; remove the roughness between bushing and pin and check the return spring.
- Air leak noise around the caliper: look for air leaks at the connection points first, since it is only indirectly related to the bushing, and check that air connections are tight.
- Dry friction noise from the caliper: grease has dried out or dust has entered; clean the old grease, renew the boot and apply new grease.
Frequently Asked Questions
When should Air Disc Brake Caliper Mechanism Bushing be replaced?
Replacement should be considered when there is clear play in the pin seat, uneven wear on the pads, or scratches on the bushing surface. Check the pin and boot at every change as well. Visual inspection alone is not enough; slide the pin by hand to test its freedom of movement.
Should bushings be bought individually or as a set?
If only one bearing is worn, a single bushing may be enough. If both pin bearings are worn, renewing them as a set is the healthier choice, because a new and an old bushing may behave differently together.
Can a bushing be used without lubrication?
The long service life of bronze and composite bushings depends on adequate lubrication. When run dry, friction increases and the pin wears quickly. Apply the correct grease during fitting, and check the boot and pin surface at service intervals.
How is a brake test done after replacing the bushing?
Park the vehicle in a safe area, fill the air pressure fully, press the brake pedal several times and observe the return time. Watch for pulling, delay or drift to one side during braking. If the problem continues, the caliper should be inspected separately.
Can an old pin be used together with a new bushing?
If the pin surface is scratched or worn, the new bushing will wear out quickly. A clean and smooth pin gives a longer service life. When deciding, feeling the clearance between pin and bushing by hand is useful.