Sheet Metal
All Sheet Metal products 11
Brake Caliper Mechanism, Sheet Metal
Brake Caliper Mechanism, Sheet Metal
Brake Caliper Mechanism, Sheet Metal
Brake Caliper Mechanism, Sheet Metal
Brake Caliper Mechanism, Sheet Metal
Brake Caliper Mechanism, Sheet Metal
Brake Caliper Mechanism, Sheet Metal
Brake Caliper Mechanism, Sheet Metal
Brake Caliper Mechanism, Sheet Metal
Brake Caliper Mechanism, Sheet Metal
No products on this page match the filter.
What is an Air Disc Brake Caliper Mechanism Sheet Metal?
An Air Disc Brake Caliper Mechanism Sheet Metal is a metal plate part used in the pneumatic disc brake calipers of trucks, buses and trailers. It is attached to the caliper body, supports the smooth movement of the moving assembly, and makes sure braking force is evenly transferred to the piston and brake pads. Working together with the piston, guide pin and spring inside the caliper mechanism, these sheet elements spread the load produced during braking evenly across the caliper body. Their role is to keep the movement path stable so the assembly travels inside the body without drifting. In the field this group is usually called simply sheet metal, while some workshops refer to it as the caliper mechanism plate. The parts that wear and take the most stress are the surfaces where the sheet contacts the body, and the seats where the guide pin and bushing sit. Over time these surfaces show crushing under load, edge wear and burr formation. This damage appears as one-sided pad wear and imbalanced braking, which makes the sheet one of the caliper group parts that is not visible but directly affects performance.
How does an Air Disc Brake Caliper Mechanism Sheet Metal work and which parts does it include?
The sheet group consists of the guide and seat elements that direct the movement of the caliper mechanism and protect the contact points inside the body. Depending on the type, the following parts may be included in this group, and each one performs a separate task.
- Bearing sheet: carries the surface where the guide pin and moving assembly seat in the caliper body and prevents drifting.
- Protection sheet: sits beside the seal and boot to reduce dust, mud and road salt entering the mechanism.
- Guide sheet: gives direction so the pad carrier arm slides smoothly and transfers its load to the body.
- Support plate: fixes the point where the piston spring and return element are attached.
- Connecting sheet: the plate that mounts the mechanism to the caliper body and carries the bolt holes.
Types of Air Disc Brake Caliper Mechanism Sheet Metal
- Single-piece sheet: preferred when only the worn or cracked element needs replacing.
- Complete sheet set: replaced as a set when several sheets must be renewed at the same time to keep surface fit.
- Left and right caliper designation: the sheet may look alike but can be made separately for each side, and it must not be fitted reversed.
How to choose the right Air Disc Brake Caliper Mechanism Sheet Metal?
Selection should be made using the removed old part. The surface marks, hole positions and edge bend of the removed sheet show which caliper type the new part belongs to. The brake system type and the axle and wheel position where the caliper body is used must also be checked. Even within the same model series of brands such as Mercedes-Benz, MAN, Scania, Volvo and DAF, layouts can differ, so choosing by model name alone is a mistake.
| Criterion | What to check | Why it matters |
|---|---|---|
| Old part | Surface marks, hole positions and edge bend | A sheet that does not match will not seat fully and causes drift |
| Caliper type | Body shape and guide pin seat | Two sheets that look alike cannot be used in different calipers |
| Side | Left or right position | A reversed sheet disturbs the load balance |
| Axle position | Front or rear use | Load and spring force vary by axle |
| Surface condition | Burrs, scratches and crushing | They make movement harder and lead to sticking |
Installation and maintenance points
- Surface cleaning: seats and contact surfaces should be brushed clean, with old rust and dirt fully removed.
- Lubrication: only the grease recommended in the service documentation, one that does not harm rubber parts, should be applied to the guide pin and the sliding surfaces of the sheet.
- Positioning: the sheet should sit in the body without force and must never be struck into place with a hammer.
- Bolt tightening: connection bolts should be tightened to the torque value specified in the service documentation.
- Checking adjacent parts: when replacing the sheet, check the seal, rubber and boot too, and renew any cracked ones together.
Common failures and solutions
- Uneven pad wear on one side: sheet sticking or burrs on the guide surface; remove the sheet, clean the surface and correct the edges.
- Delayed braking: dirt or rust blocking the sheet movement; clean and grease the surfaces, replacing the sheet if necessary.
- Hard noise during braking: crushed seats or a loose connection; check the bolts and renew the seat surface.
- Caliper sticking on release: corrosion on the guide sheet; replace the corroded sheet.
- Air leak noise from the caliper with pressure drop: usually caused by the seal or connection points rather than the sheet; look for the leak point first.
Frequently Asked Questions
Can an Air Disc Brake Caliper Mechanism Sheet Metal be replaced on its own?
Yes, only the worn or cracked part can be replaced. However, if the neighbouring sheet surface is also worn, a single part may not be enough, and renewing as a set is the more sound option in that case.
Can an old sheet be reused?
If its surface shows no scratches, crushing or clear edge wear, it can be cleaned and reused. If any of these signs is present, the part should be replaced, otherwise the seat will wear out quickly.
Should grease be used when fitting the sheet?
Yes, the grease recommended in the service documentation should be applied to the sliding surfaces. Wrong oil or excess grease can cause seals and rubber parts to swell, so the amount should be kept small.
How can you tell whether the new sheet is left or right?
Look at the markings on the caliper body and the position of the removed sheet. Parts that look alike may be marked separately for each side, so compare them before fitting.
How is the caliper tested after replacing the sheet?
The pneumatic system should be pressurized, any leak sound listened for and the pressure drop monitored. Braking balance should also be checked; if there is a leak point, check the connections first and then the sheet surface.