Washer
All Washer products 12
Brake Caliper Mechanism, Washer
Brake Caliper Mechanism, Washer
Brake Caliper Mechanism, Washer
Brake Caliper Mechanism, Washer
Brake Caliper Mechanism, Washer
Brake Caliper Mechanism, Washer
Brake Caliper Mechanism, Washer
Brake Caliper Mechanism, Washer
Brake Caliper Mechanism, Washer
Brake Caliper Mechanism, Washer
Brake Caliper Mechanism, Washer
No products on this page match the filter.
What is an Air Disc Brake Caliper Mechanism Washer?
An Air Disc Brake Caliper Mechanism Washer is the thin metal ring that spreads load over a wide area where the caliper pin and body bolts sit in air brake systems, keeping the connection seated evenly. In the workshop it is also called a flat washer or spacer washer. The part that actually wears is the surface the washer contacts; when that surface is crushed or burred, bolt tension drops over time and the caliper body begins to move and vibrate. So although the washer is small, it plays a key role in keeping the mechanism stable.
How does the Air Disc Brake Caliper Mechanism Washer work and which parts does it cover?
The washer spreads the load between the bolt head and the body, making it harder for the connection to loosen. This page covers washers only; bushings, seals and gaskets are listed in separate categories. The following parts work together in the assembly.
- Flat washer: the washer placed under the bolt head that spreads load over a wide surface.
- Lock washer: a spring or toothed design that stops the bolt from backing off after tightening.
- Spacer washer: a ring that fills the gap between two surfaces to balance the position.
- Pin and bolt set: the fasteners the washer sits under, which hold the caliper body.
Air Disc Brake Caliper Mechanism Washer types
- Flat washer: preferred for fixed connections where load spreading is sufficient.
- Spring lock washer: preferred for heavy use where vibration is high, to resist loosening.
- Toothed lock washer: used where the washer must grip the surface to prevent rotation.
- Spacer washer: chosen to close a gap between two parts or to balance the fit.
How to choose the right Air Disc Brake Caliper Mechanism Washer
Selection starts with the removed old washer and the connection point. Look at the appearance, edge design and marks left on the surface of the old washer, and determine whether it is flat, toothed or spring type. Layouts can differ even within the same model range across brands such as Mercedes-Benz, MAN, Scania, Volvo and DAF, so choosing by model name alone is a mistake.
| Criterion | What to check | Why it matters |
|---|---|---|
| Washer type | Flat, spring or toothed, and its edge design | Loosening protection depends on the type |
| Seating surface | Crushing or burrs on the contact surface | A damaged surface cannot hold the washer flat and torque drops |
| Connection point | Position between bolt head and body | A washer used in the wrong spot shifts the connection |
| Material and surface finish | Bright metal, coating or rust condition | A rusty washer does not hold torque for long |
| Replacement status | Whether it is replaced together with the bolt | Mixing old and new parts creates uneven load |
Installation and maintenance tips
- Clean the surface: no rust, dirt or old gasket residue should remain on the surface where the washer sits.
- Fit the washer in the right direction: spring and toothed washers have a directional design; fitting them backwards weakens the grip.
- Tighten the bolt in sequence: tighten the connection evenly in a crossing pattern to the manufacturer value, without pulling to one side.
- Do not reuse spring washers: a compressed spring loses its strength, so fit a new one at every removal.
- Check after vibration: after the first use, check that the bolts are still tight.
Common faults and solutions
- Bolt loosening: a flat washer was used or a spring washer has fatigued; renew it with a lock washer.
- Caliper body moves: a spacer may be missing or the surface is crushed; correct the surface and fit the right washer.
- Air leak noise around the connection: bolt tightness has dropped; check the air lines as well and replace the washer.
- Marks and scratches on the washer surface: the surface is rough or the washer was damaged during removal; replace the washer, then clean and smooth the surface.
- Vibration during braking: the caliper connection is not fully seated; check the bolt and washer set together.
Frequently Asked Questions
When should the Air Disc Brake Caliper Mechanism Washer be replaced?
Replacement is needed when the washer shows crushing, burrs, rust or lost spring strength. If the bolt was removed and refitted, the washer should not be reused as a rule. Visual inspection alone is not enough; check that the connection tightness is holding.
Can a flat washer and a spring lock washer be used interchangeably?
Both types can appear on the same connection, but a spring lock washer provides extra protection against loosening. The type should therefore be selected according to the vibration level of the connection. When changing the type, it is safer to check manufacturer data than to decide alone.
Can an old washer be cleaned and refitted?
If the washer has no crushing or marks, cleaning may be enough. Spring and toothed washers, however, do not hold tightness once used; a new one should replace them every time. When in doubt, use a new one.
How is bolt tightness checked?
After assembly, the connection should be tightened to the manufacturer value, then rechecked a short time after first use. If tightness has dropped, the bolt and washer should be evaluated together. If the bolt slides or there is a mark on the surface, tightening alone will not solve it.
Do caliper washers need changing based on vehicle age?
Replacement timing depends more on operating conditions and the condition of the connection than on vehicle age. Heavy loads, frequent braking and road vibration fatigue the connection faster. Every mark seen during removal should be considered a reason for replacement.