Washer Reservoir

Products: 4

A windscreen washer reservoir is a separate tank that supplies washer fluid to the pump and is not part of the cooling system. Read the guide

What is a windscreen washer reservoir?

A windscreen washer reservoir is a separate tank that holds washer fluid and feeds it to the windscreen washer pump, which pushes the fluid to the nozzles. Its main job is to deliver fluid to the nozzles when the driver presses the washer switch. It has no functional link to the radiator or the coolant circuit. In the field it is also known as a washer bottle, screenwash tank or windscreen washer tank. Over time, the parts that wear and leak are usually the body joints, the pump connection and the filler cap seal. For that reason, the reservoir should be checked for physical integrity, not only for the amount of fluid inside.

How does a windscreen washer reservoir work and what parts does it include?

The reservoir looks like a simple plastic container from the outside, but it contains several connected parts. Each one helps the fluid reach the nozzles evenly and without interruption.

  • Reservoir body: the main container that holds the washer fluid; it is made from plastic suited to vehicle vibration and weather conditions.
  • Filler cap and seal: prevents fluid from leaking out and limits dirt entering the tank.
  • Washer pump: pushes the fluid from the reservoir through the hoses to the nozzles; it runs on an electric motor.
  • Hoses and fittings: carry the fluid from the pump to the nozzles; rubber connectors keep the joints sealed.
  • Nozzles: spray the fluid onto the glass surface; the tip opening can become blocked by dirt over time.
  • Level float or sensor: triggers the dashboard warning when the fluid level drops.

Windscreen washer reservoir types

  • Front windscreen reservoir: the main reservoir used for the front windscreen wipers and fitted to most vehicles.
  • Rear screen reservoir: supplies separate fluid to the rear wiper and washer line; only found on models with a rear wiper.
  • Integrated pump type: the pump is built into the reservoir body, so the whole part is removed and fitted as one unit.
  • Separate pump type: the pump is independent of the reservoir; if the pump fails, only the pump is replaced and the reservoir stays in place.
  • Level sensor type: includes a sensor that shows the fill level; care must be taken with the sensor cable when removing it.

How to choose the right windscreen washer reservoir?

The safest way to choose is to read the part reference on the removed reservoir and compare it with the vehicle system type. The shape of the body, the pump mounting position, the direction of the hose inlets and the structure of the cable connector can vary from vehicle to vehicle. Even within the same model range, brands such as Mercedes-Benz, MAN, Scania, Volvo and DAF can use different layouts, so choosing by model name alone is a mistake. Photographing the hose directions and the connector before removing the old part makes matching easier.

CriterionWhat to checkWhy it matters
Reservoir shapeFit of the body to the vehicle space, corners and projectionsA wrong shape causes strain and rubbing during fitting
Pump mounting positionWhether the pump is integrated into the reservoir or separateDetermines the replacement method and the labour required
Hose inletsInlet and outlet directions, hose connection typeA wrong direction causes hose kinking and leaks
Connector structureLocking mechanism and pin layout of the cable plugA wrong connection stops the pump from working
Filler capCondition of the cap seal and cap typeDirectly affects sealing

Installation and maintenance points

  • Drain before removal: remove the reservoir only after emptying it completely, otherwise debris and dirt can enter the system.
  • Hose and fitting connections: hoses that are not fully seated on the fitting will leak; connect them without forcing or kinking.
  • Seal checks: replace the filler cap and body seal with new ones; do not reuse hardened old rubber.
  • Connector cleaning: clean the contacts to keep moisture and dirt out of the cable plug, and make sure the plug is fully seated.
  • Securing: fix the reservoir with its mounting strap and mounting points; a loose body can crack from vibration.

Common faults and solutions

  • Fluid dripping from under the reservoir: body crack, loose fitting or worn filler cap seal; a cracked body is replaced, the fitting is tightened and the seal is renewed.
  • Pump not running when the washer is pressed: pump motor cable connection, loose connector or the pump itself; the connector is checked and the pump replaced if needed.
  • Little or no fluid coming out: blockage in the hose, air leak in the suction line or an empty reservoir; the hose is checked and the leak fixed.
  • Scattered spray from the nozzle: dirt build-up at the nozzle tip; the tip is cleaned and the nozzle replaced if necessary.
  • Warning light gives false alerts: the level sensor cable or connection is faulty; the sensor plug is checked and the sensor replaced if necessary.

Frequently Asked Questions

Is the windscreen washer reservoir part of the cooling system?

No. The reservoir holds the washer fluid used by the windscreen wiper and washer line; it is not part of the engine coolant circuit. It appears in the same product group as the radiator only because of how parts are grouped.

If the windscreen washer reservoir leaks, does the whole unit need replacing?

Not always. If the leak comes from a fitting, hose or filler cap seal, only that part can be renewed. If the body is cracked, however, the complete reservoir must be replaced.

What should go in the reservoir?

Only washer fluid or a suitable screenwash concentrate should be filled. Engine coolant and other fluids can damage the pump and seals.

If the washer pump fails, should the reservoir also be replaced?

If the pump is separate from the reservoir, only the pump is replaced. On integrated types the pump comes with the body, so the whole part is renewed. In both cases, check the cable connection and the fuse before removing anything.

What should be checked after fitting?

Check that the fluid sprays evenly from the nozzles when the washer is pressed, that there are no leaks at the connection points, and that the warning light works correctly. This check should be carried out with the vehicle running and in a safe area.

Press Enter to search the full catalogue

Request a quote

Your email app opens with the request filled in.